Get Information on Aero Exhaust Silicone Straight Coupler Specification & Features Product Name: Aero Exhaust 3" Black Silicon...

Get Information on Aero Exhaust Silicone Straight Coupler

Specification & Features

• Product Name: Aero Exhaust 3" Black Silicone Straight Coupler
• Brand: Aero Exhaust

• 3" inside diameter by 3.0" long
• You can cut silicone parts down to fit with a razor knife or PVC pipe cutter
• Heat tolerance: -40° to 392° Fahrenheit Burst Pressure: 200 PSI Working Pressure: 50 PSI Wall Size: 4 mm - 5 mm Compatible with antifreeze/coolant

3" inside diameter by 3.0" long You can cut silicone parts down to fit with a razor knife or PVC pipe cutter Heat tolerance 40 to 392 Fahrenheit Burst Pressure 200 PSI Working Pressure 50 PSI Wall Size 4 mm 5 mm Compatible with antifreezecoolant

Comments List

• Aero Exhaust Silicone Straight Coupler Reviews:

  Really a great product. Installation instructions and top quality components (apart from the rods threaded Z that I preferred to changed because it was too twisted). By it against delivery by Colissimo really terrible... Avoid this mode of delivery. Its is I ordered it looking forward to the delivery! The comments almost all positive I want to buy it and I will send you my return of test to the future happy owners of this printer! Simple to use it makes it possible to use fast. For those of you that want hacks are available on the net without worries. Good 3D printer, however, the name of the article is misleading on the part of Amazon. this is not a 1. 0 AiO model corresponding to a 3D printer with integrated scanner, but a 3D printer 1. 0 HAS just. It is really necessary to read everything from A to Z. Thank you Amazon for your lack of competence in the naming of articles. The next time I would order elsewhere. By contrast, the note of the machine without scanner deserves a rating of 5 stars.

• Cheap Aero Exhaust Silicone Straight Coupler:

  A week after the order, and that I see in the followed that the printer has not moved from its repository, I called Amazon to learn that the printer has been lost (basically that someone was served) and they can't resend it right away, but they can only reimburse me for that I can recommend it. With that is added the refusal of gesture trade which in this case would have been the slightest of things: 900€ lost in the nature all the same!!! In the end I received after having registered (and 3 weeks after my first order), it works perfectly and is worthy of its reputation. An investment that's worth it if it is on as he arrives at good port! Excellent machine, perfect finish, stand-alone (computer cut off during printing). Only downside, the price of the cartridges. Still it is possible to hack itQuality product, consistent with the description made on the site. Fast shipping (UPS) but big problems for the delivery problems with UPS). Seller serious, send a reply either spontaneously the buyer by E-Mail to offer support in case of problems (in English). Only downside : product documentation non-existent, but there is a lot of information on the Internet and YouTube. I'm very happy with this 3D printer, of course, as it is a kit, there are a lot of assembly before starting. At the end of two days, I was able to make my first impressions.

• Cheap Aero Exhaust 3-Inch:

  The installation manual is clear and French, you do not ask too many questions. This is my second printer in a kit, the first being smaller and less well finished, I had already been confronted to the difficulties of 3D printing, namely adjustment of the tray, for races, printing temperature, adhesion to the support, management of the coil of wire, insertion of the filament... Here, much less surprise as my previous experience, the purposes of racing, provide a good initialization before each impression, and the integrated software that facilitates the adjustment of the level of the plateau. The support of the wire coil does its work and the insertion of the thread is simple (once one has found the button to push, perhaps too well integrated into the design of the extruder.). The chains allow a ranger and guide the wires during printing. Still problems with the adhesion of the printed pieces to the set, I haven't tried it with lacquer, I used a coating buildtak, which ensures a good grip, but with which, at approximately€ 20 the unit, I hope to be able to do a lot of impressions.

• Best Buy Aero Exhaust 3-Inch:

  The irony is that it adheres very well, so, (if one starts the print close enough to the support), the object is difficult to detach, even using a spatula fine. So, in addition to the fingers, the coating may suffer a little bit. I appreciate that the printer is 'open', as a result, the parts are produced by 3D printing and, therefore, reproducible case of a problem, or even evolutionary. And if there is a concern, I think I don't have too much difficulty to identify it and be able to correct it since I assembled the machine.. Hello, I have long studied this 3D printer. It is awesome for some things, less well for others!!! It is for that that I advise you to go see on an article that I published, it compares this 3D printer with others, it gives all the qualities and all the disadvantages of each 3D printer that I can recommend. Here it is: [... ]goodbye. Stronger I think than the wooden version. No problem, it worked the first time. Packaged well, and arrived in the time expected. A couple of things. Put a rug absorber below, I put a cutting plate provided to put underneath the equipment of a gym buy a Carrouf.

• On Sale Aero Exhaust 3-Inch:

  Because to print small parts or fine details to the head moves very abruptly and this creates strong vibrations, the engine mount horizontal broke, I reglued and the first thing I have done is to redesign it, and print it out if gluing was not... This is the benefit of fun of this type of product is that it can make its own spare parts. But now with the carpet absorbing the piece re-stuck, like the last 2 weeks. Warning the fumes of ABS are it seems to be toxic (info on the net, even if not on the principle of precaution is to be taken), the PLA is less it seems, but limited to parts which will not be moisture, PLA is biodegradable, it is all very well, but not always suitable for the purpose. Anyway there is a smell of warm plastic that emerges in use, normal the extruder that melts the plastic is 230°C. The printer is supplied without the door and top closed, unlike his twin sister of flashforge sold in the US, but not at the same price.

• Aero Exhaust 3-Inch Reviews:

  When it is a little do-it-yourselfer (to buy this type of thing it is necessarily), and that we are tired of having the window open, one buys a plate of plexi in leroy, we made templates from cardboard, a bit of cutting with the jig... to make a door and a top. An improvement of the top standard, which looks like an aquarium On the top of mine to avoid that the enclosure is fully closed as patterns of trade, without breakdown. Which I think will be a problem at the level of the engines and cables that are inside given the temperature reached 230° for wire and 110° (ABS) for the tea, I've included a fan of PC in conjunction with a flexible jacket of 80mm VMC that I put outside by the window this time as ajar, to remove the micro particles and the smell of plastic is heated directly outside, and an air flow in the enclosure. The support liaison between the fan coil and the sheath, of course, has been printed. I recommend putting a small variable speed drive (also from old pieces, PC) to adjust the speed of extraction. Because I've done tests and if you extract too strong it cooled down the support, and heated the work piece to come off of the plateau (part failed).